Index | Syntax Section 7



DBLSPACE--Notes

Creating a startup floppy disk To create a startup floppy disk if you are running DoubleSpace, use either the SYS command or the FORMAT /S command. Each of these commands creates a floppy disk that should in most cases be able to start your computer. However, to make sure, you should also copy the DBLSPACE.BIN file from the directory that contains your MS-DOS files to the root directory of the startup floppy disk. For more information about creating a startup floppy disk, see the <SYS> or <FORMAT> commands. Loading DBLSPACE.BIN into the HMA If you are running DoubleSpace and you upgraded to MS-DOS 6.22 from MS-DOS 6.2, you can load a portion of DBLSPACE.BIN into the High Memory Area (HMA). To do this, you must have an 80286 or higher computer with at least 1 MB of memory and your CONFIG.SYS file must contain a DOS=HIGH command, a DEVICE command for HIMEM.SYS, and a DEVICE command for DRVSPACE.SYS. (MS-DOS Setup and DoubleSpace Setup normally add these commands to your CONFIG.SYS file.) If you upgraded from MS-DOS 6.0, DBLSPACE.BIN cannot be loaded into the HMA; in this case, you can save about 14K of memory by converting to DriveSpace, which can load into the HMA. For more information about converting to DriveSpace, see the following section. Converting from DoubleSpace to DriveSpace If you are running DoubleSpace, you can convert your DoubleSpace drives to DriveSpace format. (If you purchased the U.S. version of the MS-DOS 6.22 Upgrade, you can obtain conversion by sending in the enclosed coupon; if you purchased the MS-DOS 6.22 Step-Up or non-U.S. version of MS-DOS 6.22, your version of MS-DOS 6.22 already includes conversion.) Note: Before converting, it's a good idea to back up the data on each DoubleSpace drive. To convert your DoubleSpace drives, type DRVSPACE at the command prompt. DriveSpace starts. To convert your drives, follow the instructions on your screen. DriveSpace converts all mounted DoubleSpace drives to DriveSpace format, and also converts your system to run DriveSpace instead of DoubleSpace. Note: The conversion process can take a long time, especially if your DoubleSpace drives contain a lot of data. You might want to plan to carry out the conversion process overnight. For more information about converting to DriveSpace, see Section 7. Keeping DoubleSpace files after conversion After conversion, do not delete any of your DoubleSpace program files, especially the DBLSPACE.BIN file and the DRVSPACE.MR1 file. These files are required in the following situations: * DriveSpace requires these files in order to convert any DoubleSpace volume files (for example, compressed floppy disks) that were not mounted during the initial conversion process. * ScanDisk requires these files to check and repair any unconverted DoubleSpace volume files. * MS-DOS 6.22 Backup for MS-DOS (MSBACKUP) requires these files to restore compressed backups created using the MS-DOS 6 or 6.2 Backup programs. (Most older backups are compressed backups, since those programs created compressed backups by default.) Using DoubleSpace drives and floppy disks with DriveSpace DriveSpace converts only DoubleSpace drives that were currently mounted during the conversion process. As a result, after the conversion is complete, you might still have some unconverted DoubleSpace floppy disks or other unmounted DoubleSpace volume files. DriveSpace can still mount unconverted DoubleSpace drives for read-only access; this means that you can read but not change the information stored on that drive. DriveSpace does not automatically mount DoubleSpace floppy disks; to mount an unconverted DoubleSpace floppy disk, you must mount it yourself by using the DRVSPACE /MOUNT command or by running DriveSpace and choosing the Mount command from the Drive menu. For DriveSpace to mount any DoubleSpace drive for full (read/write) access, you must first convert the drive to DriveSpace format. To do this, run DriveSpace, and then choose Convert DoubleSpace from the Tools menu.
-Top- | Syntax Section 7